Product Sheet
AR Standing Seam
Our Standing Seam AR metal roofing is available in 26, 24 and 22 gauge, in variable widths and with side lap rib heights of 1”, 1 ½” or 2” (27.94 mm, 38.1 mm or 50.8 mm). Agway’s AR series also features optional, two-piece expansion clips to accommodate movement of the roof, and can be seamed at either 90º or180º. With a 180º seam and optional seam caulking, panels can be used on low slopes (AR-38 down to 1.5/12 and AR-50 down to 0.5/12).
Unlike many traditional alternatives like slate or tile, our Standing Seam Profile is easy to install, more cost effective, 100% recyclable and facilitates more creativity in design. In fact, this profile can even be curved!
Whether you choose a profile from our Standing Seam, Nail Strip, or Snap Lock roof cladding systems, the result will be a stunning, architecturally distinctive roof that installs easily and has no exposed fasteners. All these durable Agway roof cladding products are available in a full range of stock colours, in variable panel widths, and with optional stiffening flutes. All are single skin applications and must be applied over a solid substrate and waterproof membrane, using clips at a maximum of 2’ centres. A full range of flashings and accessories are available from Agway to complete your project.
Resources
Measurement Type
Profile Picture
Panel Specifications
| MIN/MAX | MIN/MAX | MIN/MAX | MIN/MAX | |
|---|---|---|---|---|
| SLOPE | MATERIAL THICKNESS | SHEET LENGTH | PANEL WIDTH | |
| AR-25 | 3/12 – 12/12 | 0.018 – 0.030″ | 2′ 6″ – 45′ | 6″ – 28″ |
| AR-38 | 1.5/12 – 12/12 | 0.018 – 0.030″ | 2′ 6″ – 45′ | 6″ – 28″ |
| AR-50 | 0.5/12 – 12/12 | 0.018 – 0.030″ | 2′ 6″ – 45′ | 8″ – 24.5″ |
- Side lap caulking is recommended when the slope is less than 2/12
- Longer sheets are available. Additional charges may apply.
- For AR-25, AR-38 or AR-50 with 180 degree seam – maximum gauge is 24 GA
- Short sheet charge for any lengths under 48”
Standard Panel Widths
| GAUGE | AR-25 | AR-38 | AR-50 |
|---|---|---|---|
| 26 | 21.06″ | 20.06″ | 18.52″ |
| 24 | 21.06″ | 20.06″ | 18.52″ |
| 22 | 21.06″ | 20.06″ | 18.52″ |
Features
- No exposed fasteners
- Ease of installation
- Full range of stock colours
- Variable width
- Optional stiffening flutes
- Concealed hold-down clips
- Knee Caps available
- Optional two-piece expansion clip to accommodate roof movement
- 24 gauge can be seamed 90° and 180°; 22 gauge can be seamed 90° only
- Butyl Tape is recommended in 90° seams
- Able to be curved – minimum sheet length 5’-0”
Oil Canning
- Oil Canning is naturally occurring phenomenon inherent in all sheet steel.
- Oil Canning is not a valid reason for rejection of these products
Installation
- Single skin application
- Recommended that this always be applied over solid substrate
- Recommended that AR Series profiles be applied over waterproof membrane
- Clips at maximum 2’ centers – 2 fasteners per clip
- Mechanical and Hand Seamer required. For seamer purchase & rental visit the D.I. Roof Seamers website – or by calling D.I. Roof Installers at 1-888-343-0456
Hold-Down Clip Detail
Overlap Seaming Options
Panel Specifications
| MIN/MAX | MIN/MAX | MIN/MAX | MIN/MAX | |
|---|---|---|---|---|
| SLOPE | MATERIAL THICKNESS | SHEET LENGTH | PANEL WIDTH | |
| AR-25 | 3/12 – 12/12 | 0.457 – 0.762 mm | 0.76 – 13.71 m | 152 – 711 mm |
| AR-38 | 1.5/12 – 12/12 | 0.457 – 0.762 mm | 0.76 – 13.71 m | 152 – 711 mm |
| AR-50 | 0.5/12 – 12/12 | 0.457 – 0.762 mm | 0.76 – 13.71 m | 203 – 622 mm |
- Side lap caulking is recommended when the slope is less than 2/12
- Longer sheets are available. Additional charges may apply.
- For AR-25, AR-38 or AR-50 with 180 degree seam – maximum gauge is 24 GA
- Short sheet charge for any lengths under 1,219 mm
Standard Panel Widths
| GAUGE | AR-25 | AR-38 | AR-50 |
|---|---|---|---|
| 26 | 535 mm | 509.5 mm | 470 mm |
| 24 | 535 mm | 509.5 mm | 470 mm |
| 22 | 535 mm | 509.5 mm | 470 mm |
Features
- No exposed fasteners
- Ease of installation
- Full range of stock colours
- Variable width
- Optional stiffening flutes
- Concealed hold-down clips
- Knee Caps available
- Optional two-piece expansion clip to accommodate roof movement
- Seam can be 90° or 180° (see illustration)
- Can be used on low slopes with a caulked 180° seam:
- AR-38 down to 1.5/12 and;
- AR-50 down to 0.5/12
- Able to be curved – minimum sheet length: 1.52m
Oil Canning
- Oil Canning is naturally occurring phenomenon inherent in all sheet steel.
- Oil Canning is not a valid reason for rejection of these products
Installation
- Single skin application
- Recommended that AR Series profiles be applied over waterproof membrane
- Recommended that this be applied over waterproof membrane
- Clips at maximum 610 mm centers – 2 fasteners per clip
- Mechanical and Hand Seamer required. For seamer purchase & rental visit the D.I. Roof Seamers website – or by calling D.I. Roof Installers at 1-888-343-0456
Hold-Down Clip Detail
Overlap Seaming Options
